#Router on a stick configuration how to
#Router on a stick configuration Pc

If you want to be able to manage your switch remotely over the network, your switch needs an IP address. #2: Why do I need to configure interface вЂњvlan 1вЂќ? As soon as you change the VLAN assignment for a switch port to another VLAN, that switch port wonвЂ™t be able to communicate with the rest of the devices on other ports. With all ports in VLAN 1, all ports can communicate. By default, all ports on the switch are VLAN 1. The default VLAN on all switches is VLAN 1. Important to knowВ about configuring a Cisco IOS switch

#Router on a stick configuration Pc

Now go to PC command prompt and ping IP address, check connection. I вЂ“ IS-IS, L1 вЂ“ IS-IS level-1, L2 вЂ“ IS-IS level-2, ia вЂ“ IS-IS inter area N1 вЂ“ OSPF NSSA external type 1, N2 вЂ“ OSPF NSSA external type 2Д®1 вЂ“ OSPF external type 1, E2 вЂ“ OSPF external type 2, E вЂ“ EGP Router(config-subif)#ip address 192.168.77.1 255.255.255.0Д¬odes: C вЂ“ connected, S вЂ“ static, I вЂ“ IGRP, R вЂ“ RIP, M вЂ“ mobile, B вЂ“ BGPД вЂ“ EIGRP, EX вЂ“ EIGRP external, O вЂ“ OSPF, IA вЂ“ OSPF inter area Router(config-subif)#encapsulation dot1q 77 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.77, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.77, changed state to up Router(config-subif)#encapsulation dot1q 55 native %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.55, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.55, changed state to up Router(config-subif)#encapsulation dot1q 30 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.30, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.30, changed state to up Router(config-subif)#encapsulation dot1q 20 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.20, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.20, changed state to up Router(config-subif)#encapsulation dot1q 10 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up Sub Interfaces IP address Configure Command: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up Switch(config-if)#switchport trunk allowed vlan 1,10,20,30,55,77 Switch(config-if)#switchport access vlan 30 Switch(config-if)#switchport access vlan 20 Switch(config-if)#switchport access vlan 10 Switch(config-if)#switchport trunk native vlan 55 Switch(config-if)#switchport trunk allowed vlan 1-1005 %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan77, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down Switch(config-if)#switchport access vlan 77 Management Vlan setup and IP address assign for remote access : VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 End with CNTL/Z.ДЎ default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Ip address on interface management vlanД®nter configuration commands, one per line.

#Router on a stick configuration how to

I have showed here how to configure Inter vlan router on a stick with all command for switch and router.